Plug and play tune ECU Bmw M235i N55

  • BT-DPN55
  • New
Plug and play tune ECU Bmw M235i N55

More details

$684 $791

JB4 Plug and play tune Bmw M235i N55

Installing the downpipe requires an adjustment of the ECU map. For this we have selected a reliable and professional partner, which perfectly matches our downpipes, to solve the problem.

A plug and play additional control unit available for BMW with turbocharged engines.

The BMJB4 ECU is installed between the sensors of your car and its ECU (original ECU) going to manipulate the performance of the vehicle through these connections.

This way you can make your BMW much faster.

Although it is not the only system that works this way, it stands out from the competition with much more advanced connection and processing points including CANbus, fuel and spark control, bluetooth for the your smartphone and a variety of innovative and advanced features.

In addition to this, BMS regularly publishes free maps and firmware updates which add performance and functionality based on ongoing development.

Furthermore, the BMJB4 system is not bound to your vehicle's VIN and can be quickly removed and exchanged between cars or resold at a later time.

A control unit additional PROFESSIONAL

Different opinions and different versions of additional control units, that's why….

Perhaps you too will have doubts about the control units additional. And you do well, because most of the add-on units are a waste of money and are even deleterious.

A traditional add-on module uses a processor, because you need to start attenuate the signal only from a certain threshold (volts) and cut the same attenuation beyond another threshold.

In practical terms this means starting the"" Modulation "" when it is more appropriate to do so, for example not with the engine stopped at idle to avoid irregular idling problems; at high rpm, on the other hand, cut the modulation gradually to avoid overpressures that can send the ECU into Recovery mode.

On a technical level all this means that the signal should be attenuated after the 1.15 volts and then gradually cut towards about 4 volts.

Basically the module allows you to get the maximum Rail pressure where your car and the ECU can tolerate it.

With this type of processing it will never be possible to exploit all the potential that a good remapping can offer.

But there is an alternative that is equivalent to mapping, that is the JB4 control unit.

The Jb4 control unit is not a simple additional module, but a real control unit that gives you the possibility to decide what to do, also allowing you to load a customized map.

It is a high-level professional tool that leaves maximum freedom of use.

What you can achieve

With the Jb4 module you have total control of engine performance.

I the advantages of this control unit are innumerable.

First you need to know that you have 7 maps to select (even on the move).

Map 0 : JB4 disabled, stock performance
Map 1: Increase the pressure by 4psi
Map 2: Increase the pressure by 6psi, ideal if you mount the Downpipe for example.
Map 3: Progressive Sports Map that eliminates dispensing holes.
Map 4: Standard performance but JB4 active, allows you to collect data and analyze them to prepare a map
Map 5: Self-adaptive Racing Map, increases the pressure from 11 to 17psi, ideal for intense preparations.
Map 6: Empty map, you can load it by inserting the various parameters.
Map 7: Race Gas map. Increase the pressure up to 18.5psi. For extreme preparation.


As you can see inside the control unit you already have a series of maps loaded, but using map 6 you can decide to manage the engine as you wish, setting the parameters according to the needs of the engine.

The JB4 also allows you to extrapolate data from the engine.

In addition to this it allows you to manage other parameters, and I'll tell you about two examples.

The first is that you can decide to always keep the exhaust valve open, by commanding the opening and closing directly from Jb4.

In addition to this (and many other functions) you can also read and delete OBD errors.

This is an advantage, because when you mount the downpipe the engine warning light will come on.But with the JB4 this does not happen.

For this we recommend the JB4 ECU, because it is perfectly compatible with our Downpipes.

By buying the ECU and Downpipe you can install everything directly, without going to the workshop and running out of a machine.

Installation is quick and easy. On some models it mounts and manages without additions, on others a cable or a Bluetooth module may be needed to transfer data. These items must be purchased separately, they are NOT included.

Another advantage of this control unit is that you can remove it at the time of servicing or in case of problems under warranty.

As the car returns to its original state as soon as the control unit is removed.

Due to its features and functions we are sure to recommend this engine control unit for your BMW, which has been built around the world for over 12 years. We are the distributor in Italy of the JB4 brand of Burger Motorsport